![mazak alarm codes mazak alarm codes](https://img.dokumen.tips/img/1200x630/reader012/image/20180324/55cf941d550346f57b9fb744.png)
The position where the one-rotation signal of the α position coder, BZ sensor, MZ sensor, α position coder S is incorrect. The one-rotation signal for Cs contour control is not generated. Incorrect data ROM type for Cs contour control detector circuit or incorrect setting. This alarm is not issued when the parameter indicated below is not set. The position where the one-rotation signal for Cs contour control is generated is incorrect. Incorrect parameter setting for the number of speed feedback pulses. This alarm is issued also when the motor is not deactivated (the motor is not decelerated completely) when the acceleration/deceleration time (initial parameter setting: 10 seconds) has elapsed after emergency stop signal input.
![mazak alarm codes mazak alarm codes](https://cnc-electronics.com/wp-content/uploads/dnc48-back-768x512.jpg)
The gear ratio set in a parameter exceeds the value range allowable for internal processing.Īfter emergency stop signal input, the motor is accelerated without being decelerated. This alarm is issued with a parameter related to orientation of magnetic sensor type. The gear ratio set in a parameter exceeds the value range allowable for internal processing. Parameter data outside the specifiable range was set. The PSM could not be charged within a specified time. A check is made when the power is turned on.
Mazak alarm codes serial#
LSI memory for serial communication is abnormal. The motor failed to rotate as specified, and has stopped or is rotating at a very low speed. The sensor signal (for position control) for Cs contour control is abnormal.Īn excessive load (standard setting: load meter reading of 9 V) has been applied continuously for a certain period (standard setting: 30 seconds).Īn excessively large current is detected at the input of the 3-phase main circuit of the PSM. The sensor signal (position coder signal) for position control is abnormal. The sensor signal (for speed control) for Cs contour control has an error. Serial communication between the CNC and spindle amplifier module stopped. (This symptom does not represent an error.) Serial communication data transferred between the CNC and spindle amplifier module contains an error. Position sensor polarity setting incorrect The offset voltage of the phase V current detection circuit is excessively high. The offset voltage of the phase U current detection circuit is excessively high. Spindle switch/output switch sequence faulty. Option alarm, possible spindle switch/output switch sequence faulty. Spindle switching operation sequence was not executed correctly. PSM detected that the DC link voltage was excessively high.Įxcessively large current flowed into the DC link of the main circuit. Temperature of the heat sink of the SPM main circuit has risen to the set value. The motor rotates at a speed exceeding 115% (standard setting) of the maximum allowable speed. The temperature sensor is abnormal in the motor, or the temperature sensor cable is broken. Parity error was detected in the SRAM on the SPM control PCBĪctual motor speed is largely deviated from the commanded speed.įaulty regen circuit or DC link circuit is faultyĭetected that the 3-phase input to the main circuit of the PSM has an open phase.ĭetected that the 3-phase input has an open phase. Unit is not ready or not commanded to run.Īmplifier is ready (normal operating state)Įrror was detected in SPM control program processing.Įrror was detected in the clock of the SPM control PCB.
Mazak alarm codes code#
Fanuc Spindle Amplifier Alarms Alarm Code
Mazak alarm codes free#
You’ll get free over-the-phone support and, if necessary, a quote for FANUC spindle amplifier repairs, a new FANUC spindle amp module or FANUC AC spindle amp. If you’ve tried everything, scoured every alarm code list you can find and still can’t get your part back in production, contact us today.
Mazak alarm codes series#
FANUC Alpha, Alpha i series & Alpha is series.
![mazak alarm codes mazak alarm codes](https://i.ytimg.com/vi/iyexPfkunlA/maxresdefault.jpg)
If your CNC machine tool is throwing an error you need to track down the source of the problem-which isn’t always as easy as it sounds. Tri Star CNC Services helps you diagnose and troubleshoot your FANUC spindle amplifier and other electronic components.